MOBILE
|
|
MOBILE
|
|
Press and hold the button and the Power (MEAS) button simultaneously until the boot screen changes to a calibration screen showing CAL .
Based on standard industrial equipment manuals, the DT50 PDF would likely include:
Used to add or subtract multiple measurements or navigate saved data.
When you first open the DTAPE DT50 packaging, the box should contain the following items:
| Section | Content | | :--- | :--- | | | Laser class (Class II, <1mW at 620-690nm), eye safety, battery handling. | | 2. Device Overview | Diagram of buttons (Power/Measure, Area/Volume, Reference shift, Bluetooth). | | 3. Basic Operations | Single measurement, continuous measurement (tracking), min/max functions. | | 4. Advanced Modes | Area (length x width), Volume (length x width x height), Indirect (Pythagoras). | | 5. Bluetooth & Data | Pairing with apps (dTape Link), sending measurements to spreadsheets. | | 6. Settings Menu | Unit switching (ft/in, decimal feet, meters), backlight timeout, calibration. | | 7. Maintenance | Cleaning the lens, battery replacement (2 x AAA), storage. | | 8. Error Codes | Err 1 (Battery), Err 2 (Signal too weak), Err 3 (Measured range exceeded). | | 9. Specifications | Range (50m/165ft typical), accuracy, IP rating (usually IP54). |
Press it to switch between the (starts from the laser beam exit) and Rear Reference (includes the length of the device body). Manual Calibration (Offset Adjustment)
A short press switches the measurement reference point (front of the device vs. back of the device). A long press toggles measurement units (m/in/ft).
Long press changes the measurement unit. Short press changes the reference point (front vs. back of the device).
Long-press the OFF/CLR button for 2 seconds. (The device also features automatic shutdown after a period of inactivity to save battery). 2. Changing Units
The device automatically calculates and displays the total square footage or square meters on the main line. Volume Calculation ( ft3f t cubed
The target surface is not reflecting the laser properly. Hold a piece of white paper or a target plate over the destination spot to improve reflection.
Press the button twice until a 3D cube icon appears on the display. Press MEAS to record the Length. Press MEAS to record the Width. Press MEAS to record the Height.
Goal: Create an engaging, searchable, and interactive feature that helps users find, read, and get actionable help from the DTape DT50 user manual PDF.
Use a white target sheet or piece of paper on the destination surface. Ambient light is too bright
If you are looking for the official documentation, you can access the DTAPE DT50 User Manual on Manuals+ or view a downloadable DT50 Guide on Scribd . These manuals provide detailed instructions on setup, safety, and advanced measurement modes. Key Specifications
The device can measure from the front edge or the rear edge. Long-press the button to switch the reference point. This is crucial for accurate measurements, such as measuring from a wall. 4. Taking a Single Measurement Press READ to activate the laser. Point the laser at the target. Press READ again to take the measurement. 5. Continuous Measurement (Tracking) Long-press the READ button.
Keep the device at a strict 90-degree angle for the second shot. The DT50 will calculate the vertical height (Leg) automatically. How to Calibrate the Dtape DT50
Press and hold the button and the Power (MEAS) button simultaneously until the boot screen changes to a calibration screen showing CAL .
Based on standard industrial equipment manuals, the DT50 PDF would likely include:
Used to add or subtract multiple measurements or navigate saved data.
When you first open the DTAPE DT50 packaging, the box should contain the following items:
| Section | Content | | :--- | :--- | | | Laser class (Class II, <1mW at 620-690nm), eye safety, battery handling. | | 2. Device Overview | Diagram of buttons (Power/Measure, Area/Volume, Reference shift, Bluetooth). | | 3. Basic Operations | Single measurement, continuous measurement (tracking), min/max functions. | | 4. Advanced Modes | Area (length x width), Volume (length x width x height), Indirect (Pythagoras). | | 5. Bluetooth & Data | Pairing with apps (dTape Link), sending measurements to spreadsheets. | | 6. Settings Menu | Unit switching (ft/in, decimal feet, meters), backlight timeout, calibration. | | 7. Maintenance | Cleaning the lens, battery replacement (2 x AAA), storage. | | 8. Error Codes | Err 1 (Battery), Err 2 (Signal too weak), Err 3 (Measured range exceeded). | | 9. Specifications | Range (50m/165ft typical), accuracy, IP rating (usually IP54). | dtape dt50 user manual pdf
Press it to switch between the (starts from the laser beam exit) and Rear Reference (includes the length of the device body). Manual Calibration (Offset Adjustment)
A short press switches the measurement reference point (front of the device vs. back of the device). A long press toggles measurement units (m/in/ft).
Long press changes the measurement unit. Short press changes the reference point (front vs. back of the device).
Long-press the OFF/CLR button for 2 seconds. (The device also features automatic shutdown after a period of inactivity to save battery). 2. Changing Units Press and hold the button and the Power
The device automatically calculates and displays the total square footage or square meters on the main line. Volume Calculation ( ft3f t cubed
The target surface is not reflecting the laser properly. Hold a piece of white paper or a target plate over the destination spot to improve reflection.
Press the button twice until a 3D cube icon appears on the display. Press MEAS to record the Length. Press MEAS to record the Width. Press MEAS to record the Height.
Goal: Create an engaging, searchable, and interactive feature that helps users find, read, and get actionable help from the DTape DT50 user manual PDF. How to Calibrate the Dtape DT50
Use a white target sheet or piece of paper on the destination surface. Ambient light is too bright
If you are looking for the official documentation, you can access the DTAPE DT50 User Manual on Manuals+ or view a downloadable DT50 Guide on Scribd . These manuals provide detailed instructions on setup, safety, and advanced measurement modes. Key Specifications
The device can measure from the front edge or the rear edge. Long-press the button to switch the reference point. This is crucial for accurate measurements, such as measuring from a wall. 4. Taking a Single Measurement Press READ to activate the laser. Point the laser at the target. Press READ again to take the measurement. 5. Continuous Measurement (Tracking) Long-press the READ button.
Keep the device at a strict 90-degree angle for the second shot. The DT50 will calculate the vertical height (Leg) automatically. How to Calibrate the Dtape DT50
FF Node © 2026